Xh9950 manual

If you are just forwarding a single port number then you can simply enter that same number into both the Start Port Number and the End Port Number boxes.

If you are forwarding a range of ports, usually separated by a hyphen, then you need to enter the lowest number of that range into the Start Port Number box and then enter highest number into the End Port Number box.

This is either the IP address of a computer or the IP address of another device on your network. To test if your port has been properly forwarded, you can use our Network Utilities tool, which includes a free Open Port Checker. We also have the Internets largest collection of Router Screenshots.

You can connect with more players in Madden NFL 22 and help improve connections by forwarding some ports. You can forward some ports in your router to help improve your online connections in Microsoft Flight Simulator. You can help improve connections and make it easier to connect with co-op partners in It Takes Two by forwarding some ports. Whether playing co-op with your buddies or competitive versus the world, Ghost Recon: Breakpoint is better with ports forwarded.

Note: Once you have completed the quick start setup, any computer with a wireless network card will have access your network. To avoid this situtaion please add security to your wireless network, details on adding security to your wireless network are given under section 5. To start the quick start setup, select the Quick Start option from the main menu. This will open a new window please ensure that your browsers pop up blocker does not block popup windows from To ensure the security of your network you will be prompted to change the admin account password of your router, enter the new password twice in the provided text boxes and click Next.

Note: The username is not always the same as your email address, in some cases the suffix may be different for example Xtra users use username.

Click Next to save the changes you have made, the router will prompt you to enter the new admin account password which was entered in step 3 above. Once the password has been entered and confirmed the router will confirm that the settings have been changed, click Close to finish the quick start setup. In this Device, you can totally setup 8 VCs on different encapsulations, if you apply 8 different virtual circuits from your ISP. You need to activate the VC to take effect. This option is typically used for Cable services.

You will need to enter in the Connection type, IP address, subnet mask, and gateway address, provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which is four IP octets separated by a dot x.

The Router will not accept the IP address if it is not in this format. This option is typically used for DSL services. Bridges are devices that enable two or more networks to communicate as if they are two segments of the same physical LAN. Connect on demand is dependent on the traffic. If there is no traffic or Idle for a pre-specified period of time , the connection will be dropped automatically.

Once there is traffic send or receive, the connection will be automatically on. Direction: Select this option to specify the RIP direction. None is for disabling the RIP function. Both means the ADSL Router will periodically send routing information and accept routing information which then gets added into the routing table. Select None to disable it. You will also have to enter a subnet mask to suit the IP address. The DHCP address pool contains the range of the IP address that will automatically be assigned to the clients on the network.

Each of the device's interfaces can be configured as a DHCP relay. To have this function working properly, please run on router mode only, disable the DHCP server on the LAN port, and make sure the routing table has the correct routing entry. Enter a value between 20 and A beacon is a packet broadcasted by the Router to synchronize the wireless network. This option requires a value between 0 and It is the maximum data fragment size that can be sent. This options requires a value between and Select Disabled to completely remove security.

Select Disable to allow all wireless computers to communicate with the access points without any data encryption. If you chose bit WEP, then enter any 10 hexadecimal digits "", "A-F" preceded by 0x for each key If you chose bit WEP, then enter 26 hexadecimal digits "", "AF" preceded by 0x for each key The values must be set up exactly the same on the Access Points as they are on the wireless client stations. The same value must be assigned to Key 1 on both the access point your ADSL Router and the client adapters, the same value must be assigned to Key 2 on both the access point and the client stations and so on, for all four WEP keys.

You may use one of the four keys at any time. Pre-shared Key: The Pre-shared Key is used to encrypt data. Select Allow Association to permit access to the router, MAC addresses not listed will be denied access to the router.

IP Subnet Mask: Enter the destination subnet mask. Metric: Metric represents the "cost" of transmission for routing purposes. IP Routing uses hop count as the measurement of cost, with a minimum of 1 for directly connected networks. Enter a number that approximates the cost for this link. The number may not to be precise and should be between 1 and In practice, 2 or 3 is usually a good number.

If set to Yes, the route to this remote node will be propagated to other hosts through RIP broadcasts. If No, this route is kept private and is not included in RIP broadcasts.

It can be single IP or multiple IPs. It prevents outside users from getting direct access to a server that has company data. Users of the public network outside the company can access only the DMZ host. You can specify 10 rules in maximum. If it is one port only, you can enter the End port number the same as Start port number. For example, you want to set the FTP Virtual server; you can set the start and end port number to The update may be created to address bugs in the previous firmware, to optimise some internal functions or to add new features.

We do not recommend that you upgrade the firmware unless it specifically addresses a problem you currently have or has a new feature that you may absolutely need if its not broken, dont fix it! Simply drop your router into your nearest Dick Smith Electronics store throughout New Zealand it will be packed up and shipped to our Auckland Service Centre where our qualified technicians will perform the upgrade, test your router with the new firmware, and then return it to the store for you to collect, however, this may take working days and DSE may not be able to provide a solution for your to use your internet in the meantime.

To perform a router firmware upgrade, first make sure that you have downloaded the correct firmware and if it is a zipped file then it should be unzipped to an easily accessible folder. Log into the Router and navigate to Maintenance Firmware. Click on Browse button under New Firmware Location and navigate to the location where the updated firmware is saved. The update process will take about two minutes to complete.

Utility Engines. Snow Blower Engines. Portable Generators. Energy Storage Systems. Commercial Generators. Home Generators. Pressure Washers. Snow Blowers. Lawn Mower Maintenance. Engine Parts. Equipment Parts. Parts Lookup Tool. Owner Support. Register Product. Locate Model Number. Dealer Locator. To ensure the security of your network you will be prompted to change the admin account password of your router, enter the new password twice in the provided text boxes and click Next.

Page 18 5. Note: The username is not always the same as your email address, in some cases the suffix may be different for example Xtra users use username. Click Next to save the changes you have made, the router will prompt you to enter the new admin account password which was entered in step 3 above.

Once the password has been entered and confirmed the router will confirm that the settings have been changed, click Close to finish the quick start setup. Page Interface Setup 5. Bridges are devices that enable two or more networks to communicate as if they are two segments of the same physical LAN. Direction: Select this option to specify the RIP direction. Page Wireless 5. Enter a value between 20 and A beacon is a packet broadcasted by the Router to synchronize the wireless network.

Select Disable to allow all wireless computers to communicate with the access points without any data encryption. Page 28 Metric: Metric represents the "cost" of transmission for routing purposes.